Behind the part amount a suffix of “H” is added if the teeth are hardened from being heat-treated. If the sprocket is a QD or taper bushed style the guts letter for the hub designation is definitely changed to represent therefore.
Regular Sprocket With Finished Bore Example:
Some manufactures will also designate in the component number if the sprocket is manufactured from a particular material. This designation can be placed in the front of the part number or behind, if it’s noted.
Bottom Diameter (BD) – This is the measurement of the diameter of a circle tangent to the bottoms of the tooth areas.
Caliper Diameter – Because the bottom diameter (BD) of a sprocket with odd quantity of teeth can’t be measured directly, caliper diameters are the measurement over the tooth spaces nearly opposite.
Pitch Diameter (PD) – The diameter across to the pitch circle which may be the circle accompanied by the centers of the chain pins because the sprocket revolves in mesh with the chain. PD= PITCH/ SIN(180/nT)
Outdoors Diameter (OD) The outside diameter is the measurement from the tip of the sprocket tooth across to the corresponding point directly across the sprocket. It is comparatively unimportant as the tooth size is not essential to appropriate meshing to with the chain. The exterior diameter may vary based on the type of cutter used. OD=(pitch)(0.6+COT[180/nT])
Hub Diameter (H) – Is the distance over the hub from one side to some other. This diameter should never surpass the calculated diameter of the inside of the chain sidebars.
Maximum Sprocket Bore – This dimension depends upon the required hub wall structure thickness for proper power. The dimensional allowance must be made for keyway and set screws.
Face Width (T) – Face width is limited in its optimum dimension to allow proper clearance to provide for chain engagement and disengagement. The minimal width is limited to provide the proper strength to carry the imposed loads.
Length Thru Bore (L) – The length thru bore must be sufficient to allow an extended enough key to withstand the torque transmitted by the shaft. This also actions the balance of the sprocket on the shaft.

ANSI-CERTIFIED ROLLER CHAIN SPROCKETS
Industrial chain sprocket breakages can bring your machinery to a grinding halt. Many machines can’t operate without their drive train sprockets, and replacing them can cost a lot of time and money. Additionally, the efficiency of a conveyor or drive depends on sprocket-chain interaction. Using the proper sprocket is simply as important as deciding on the best chain. At Ever-power Roller Chain, we provide a wide selection of regular roller chain sprockets at unbeatable prices. Our sprockets are designed to execute well under pressure and are resilient. The roller chain sprockets for sale in our store include single-strand roller chain sprockets, double strand sprockets and multi-strand roller chain sprockets. Furthermore, our drive chain sprockets meet both ANSI and ASME standards.
We’re positive you’ll become happy when you buy industrial chain sprockets inside our store, because they’ll last you quite a long time. If you’re uncertain what sprockets will be the ones you will need for your machine, please don’t hesitate to give us a contact. Our knowledgeable staff, excellent items, and unbeatable prices are the reasons for our A+ BBB ranking!
One STRAND ROLLER CHAIN SPROCKETS
There are six different standard varieties of sprockets for single strand roller chain. We share a complete line of each type! Our standard one strand roller chain sprockets are produced with hardened tooth (for tooth counts under 30), used high quality quality SAE 1045 steel material, and are completed with black-oxide for corrosion resistance.
To start shopping simply select what chain size you are employing with your sprocket. Next select the type needed, lastly select the desired tooth count and feasible accessories needed, then you are ready to obtain your sprockets! If at any point you have queries or difficulty finding or selecting your sprocket please contact our customer support department and we’ll be happy to assist you.
DOUBLE SINGLE SPROCKETS
Double one sprockets are created to operate two single-strand type roller chains, that’s where the name “double single” came from. Typically these sprockets certainly are a design but both BTB taper bushed and QD style is available from share. Our double single sprockets are manufactured with hardened teeth and have a black oxide coating for excellent performance and hook corrosion resistance. Share sizes of double solitary sprockets range between ANSI #40 – #160 but additional sizes could be manufactured upon request. We are able to also supply quick reaction custom re-bores and MTO specialty double single sprockets because of our quick reaction in-house machine shop. Something vital that you note is that even though these sprockets are double sprockets they will not double-strand roller chain. The charts below show the in-stock double one sprocket sizes and have clickable links to the merchandise pages themselves.
ROLLER CHAIN SPROCKET NOMENCLATURE
Different sprocket manufactures make use of different “terms” or nomenclature to describe their sprockets. Though, throughout the general background of roller chain sprockets nearly every produce utilizes four various kinds of sprockets and has followed the same nomenclature for them.
STANDARD SPROCKET STYLES
Style A, also called A-Plate or simply “plate sprocket” is definitely a flat sprocket plate-wheel with no hubs that extrude on either side.
Style B, also referred to as B-Hub sprockets is a sprocket with a hub that extrudes using one side.
Style C, also referred to as C-Hub sprockets can be a sprocket with a hub that extrudes on both sides.
Style D, is a sprocket with a detachable bolt-on hub attached to a plate.
MULTI-STRAND ROLLER CHAIN SPROCKETS
Multi strand roller chain sprockets will start with a prefix except when past 4-strands. We supply single through twelve (12) strand roller chain sprockets in the four regular styles along with various other styles upon request.
D – Dual Roller Chain Sprockets/ Duplex Sprockets
Electronic – Triple Roller Chain Sprockets/ Triplex Sprockets
F – Four Strand Sprockets/ Quadruple Sprockets
DS – Double Single (these sprockets are created to operate two single-strands of roller chain part parallel to each other)
COMMON SPROCKET STYLES
QD design sprockets, also known as “quick detachable” utilize a tapered bushing that’s bolted into the bore that’s machined in the sprocket. When the bushing is definitely inserted in to the sprocket is compresses onto the shaft, which gives a tight grip.
Taper Bushed sprockets, commonly designated with TL, BTL, CTL, TB, BTB, or CTB is another design of interchangeable bushed sprockets that delivers a positive grip on the driven shaft.
Shear Pin sprockets use a shear pin type hub that is bolted to a sprocket to supply an overload device. If the torque rating is exceeded the shear device disengages the sprocket from the drive.
Split type roller chain sprockets are produced for quick installation with no disruption of the shaft and alignment.
SPROCKET PART NUMBER NOMENCLATURE
When identifying a sprocket with a part number, standardly the chain pitch will be written first, then your hub design or code, and followed by the number of teeth the sprocket has. If the sprocket is certainly multi strand there will most often be a letter prefix at the start of the part number.